4 Κοινά Σφάλματα και Λύσεις από Αέριο Ανιχνευτές
Σφάλμα 1. Χαμηλή συγκέντρωση αέριο δεν μπορεί να ανιχνευθεί
solutions%3α
1. Check if the air pump of the gas detector is working normally. Block the air inlet with your finger for 5 seconds. If there is obvious suction, if there is no suction, check if if the air inlet is blocked;
2. Εισαγωγή άζωτο αέριο σε βαθμονόμηση το μηδέν σημείο ή βαθμονόμηση το μηδέν σημείο in καθαρός αέρας, και μετά δοκιμή μετά βαθμονόμηση;
3. If the measured gas cannot be detected after zero point calibration, the gas detector needs to be restored to factory settings;
4. The above steps have been performed but still can not be detected. It is necessary to confirm whether there is a gas to be measured on site, or the concentration of the gas to be measured is really low. If it is lower than the small detection accuracy of the gas sensor, it cannot be detected.
Fault 2. In the air, there is no measured gas, but the value fluctuates greatly or jumps wildly
solutions%3α
1. The short-term zero point fluctuation range is less than 1 percent of the large range, which ανήκει to the normal range. In the absentence of the measured gas, the long-term drift is less than 2 percent of the large range. Gas, or the temperature and humidity in the air fluctuate greatly, resulting in unstable values;
2. Επιβεβαίωση εάν το μηδέν σημείο βαθμονόμηση ή στόχος σημείο βαθμονόμηση λειτουργία έχει εκτελεστεί on το αέριο ανιχνευτής. Εάν ο μηδέν σημείο βαθμονόμηση λειτουργία εκτελείται στο το τόπος όπου υπάρχει α αέριο σε να είναι μετρημένο, it μπορεί όχι be able to ανίχνευση χαμηλή συγκέντρωση αέρια. Ο στόχος σημείο βαθμονόμηση εκτελείται, αλλά το βαθμονομείται συγκέντρωση τιμή κάνει δεν ταίριασμα το πραγματική συγκέντρωση τιμή, που μπορεί προκαλεί το τιμή του του αερίου ανιχνευτή να διακύμανση πολύ ή το ανιχνεύεται τιμή είναι πάρα πολύ μικρό. Αυτά δύο καταστάσεις μπορούν είναι επιλυμένα από αποκατάσταση το εργοστάσιο λειτουργία%3β
4. If the problem cannot be solved, it is necessary to confirm if the gas detector is fed with high-concentration gas and high-concentration gas has impact the gas sensor. if it has impacted the gas sensor, turn on the gas detector and run it for 24 hours. if the value is still unstable, the gas sensor may be damaged by impact, and the gas sensor needs to be replaced.
Σφάλμα 3. Ανακριβής ανίχνευση
1. Επιβεβαίωση εάν το αέριο συγκέντρωση στο τοποθεσία είναι ακριβές. Η διαφορά μεταξύ το θεωρητική τιμή και το πραγματική τιμή είναι μεγάλο. βαθμονόμηση το αέριο ανιχνευτής με εισάγοντας πρότυπο αέριο σε διασφάλιση το ακρίβεια του του ανίχνευση, ή αποστολή it σε α τρίτος μέτρηση ίδρυμα για επαλήθευση και βαθμονόμηση%3β
2. If the gas sensor is used for a long time, there may be errors in the measured value. It is necessary to confirm with the manufacturer if the gas sensor can continue to be used. If the sensor is approaching its its service life, it can be normal in a short time even after recaliation It is used, but the measured value of the gas detector will drift and the detection θα είναι ανακριβής. Αυτό είναι συνιστάται να αντικαταστήσει το αέριο αισθητήρας.
Fault 4, when the value is 0 or the alarm value is not reached in the air, it will also alarm
solutions%3α
1. Check whether the various alarm value parameters of the gas detector have been modified;
2. Έλεγχος αν ο συναγερμός λειτουργία και συναγερμός τρόπος του αέριο ανιχνευτής έχουν τροποποιηθεί;
3. Έλεγχος εάν ο συναγερμός κατάσταση του του αερίου ανιχνευτής είναι a συγκέντρωση συναγερμός ή άλλο σφάλμα συναγερμός % 2c η συγκέντρωση συναγερμός θα εμφανιστεί A1 ή A2% 2c και το κόκκινο δείκτης φως θέληση φλας ;
4. If the gas detector alarm caused by manual modification can be solved by restoring the factory settings, the fault alarm needs to be further checked for short circuit, open circuit, poor contact, sensor failure, etc., or sent back to the manufacturer for inspection.
